warpfeed to angel lcd?

Brian · 2002-05-13 17:30:17

I have seen some finnish players use angel with warpfeed,
do you use sens mode, or do you connect wires inside the grip to trigger impuls, or is it possible to use + mode and sense mode and hook it up to the intelifeed , let me know how you use the warpfeed,moikka Brian.....

shwoomie · 2002-05-13 18:03:26

i think it is best to use the trigger plug because the vibration sensor might not work properly because of the low recoil/kick on angel...you can find the install instructions at http://www.airgun.comthere should be manuals for impulse,angel lcd,automag,and some others

/edit/ i think it is possible to use both intellifeed and warp feed because warp only takes the trigger impulse and spins when it gets the impulse (same as intellifeed?) so they both should be useable at the same time...NOTE: this just my unschooled recollection of how think it is done so do it at your own risk..../edit/

joona/unknown

Brian · 2002-05-14 15:53:02

Thanks for the advice ,i will hook it up to the trigger i think, Moikka Brian..

Howari · 2002-05-16 16:38:18

Brian,

DO NOT hook up the Warp interface leads to the trigger leads!

Instead, hook the interface leads to the solenoid leads, because the Warp needs to sense atleast a 5 volt signal from the marker´s firing sequence. The output from the Angel solenoid leads is approx. 6 volts. NOTE: You cannot necessarily trust that the colouring of the leads is correct on the Angel. The red lead to solenoid can be a ground lead as well! (I´ve come across a couple of such Angels!!!)

Then, switch the 3-jumper bank with a jumper only in the center socket!!! (+)

However, please visit the AGD tech resources docs at <a class="postlink" href="http://www.airgun.com">www.airgun.com</a> to get the illustrated instructions!

Cheers,

Howari/DT

Wannabe

Brian · 2002-05-17 16:24:11

I looked at airgun.com and did same as you wrote about,and yes the wires were mixed up but now it`s working fine, have to try it out soon, moikka Brian...

Jantune · 2002-05-23 20:02:50

Toimiikos tämä systeemi kunnolla lcd:ssä?? Ettei tule turaostosta...

Jantune

shwoomie · 2002-05-23 20:19:14

en oo saletti mikä enkeli yhellä poppoo kaverilla on kun en oo enkeli tuntija mutta ihan hyvin näyttäis toimivan!!!

joona/Unknown

Howari · 2002-05-23 20:53:08

Jantune,

Ihan hyvin toimii, kunhan vaan liität ne Warp Interface- kaapelin johdot kunnolla enkelin solenoidijohtoihin. Toisin sanoen, kuorit solenoidijohdot ~sentin matkalta ja juotat interface-kaapelin johdot niihin sekä pidät huolen liitosten huolellisesta eristämisestä.(kannattaa tosiaan varmistua solenoidijohdoista, että kumpi on maa- ja kumpi + johto, ENNENKUIN juotat liitoksen...)

Yksi vaihtoehto on katkaista solenoidijohdot ja sitten suorittaa em. toimenpiteet, jolloin voit käyttää kutistesukkaa liitoksen eristämiseen.

T:Howari/DT

Wannabe

Jantune · 2002-05-24 13:16:31

Howari kiitoksia hyvistä neuvoista ja täten turvallisin mielin warppi tilaukseen

Ja tuoltapa löytyykin aika selvät kuvat ja ohjeet asennuksesta...

Jantune / Raaka Kone

Splatboard

#1 2002-05-13 17:30:17

Re: warpfeed to angel lcd?

#2 2002-05-13 18:03:26

Re: warpfeed to angel lcd?

#3 2002-05-14 15:53:02

Re: warpfeed to angel lcd?

#4 2002-05-16 16:38:18

Re: warpfeed to angel lcd?

#5 2002-05-17 16:24:11

Re: warpfeed to angel lcd?

#6 2002-05-23 20:02:50

Re: warpfeed to angel lcd?

#7 2002-05-23 20:19:14

Re: warpfeed to angel lcd?

#8 2002-05-23 20:53:08

Re: warpfeed to angel lcd?

#9 2002-05-24 13:16:31

Re: warpfeed to angel lcd?

Keskustelualueen alatunniste